Power EdgerOperator's ManualMODEL PE-200Serial Number 05001001 - 05045500X77000068003/03X7702275300WARNING DANGERRead rules for safe operat

10ASSEMBLYDRIVE SHAFT/POWER HEADTools Required: 8 x 10 mm Spanner WrenchParts Required: Power Head, Drive Shaft Assembly1. Stand engine on a level sur

POWER EDGEROPERATOR'S MANUAL11PRE-OPERATIONFUELFuel RequirementsGasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline knownto be good q

12OPERATIONSTARTING COLD ENGINEWARNING DANGERThe attachment will operate immediately when the engine startsand could result in loss of control a

POWER EDGEROPERATOR'S MANUAL13STARTING WARM ENGINEThe starting procedure is the same as Cold Start except DO NOT closethe choke, and do not depre

14OPERATING TECHNIQUES1. Before edging, water the area to soften the ground to make edgingeasier.2 Before edging, check the area and remove all obstac

POWER EDGEROPERATOR'S MANUAL15MAINTENANCEYour ECHO edger is designed to provide many hours of trouble free service. Regular scheduled maintenance

16AIR FILTERLevel 1.Tools required: Cleaning brush 25 or 50 mm (1 or 2 in.)Parts required: 90008 REPOWERTM Air & Fuel Filter Kit1. Close choke (Co

POWER EDGEROPERATOR'S MANUAL170.65 mm(0.026 in.)SPARK PLUGLevel 2.Tools Required: T-Wrench, Feeler gauge, Soft metal brush.Parts Required: REPOWE

181. Remove spark plug lead from spark plug.2. Remove muffler cover bolt (A).3. Remove four screws that retain the engine cover. Two at the top ofthe

POWER EDGEROPERATOR'S MANUAL19Cylinder Exhaust PortLevel 3.IMPORTANTThe cylinder exhaust port must be inspected and cleaned of excesscarbon every

2Copyright© 2003 By Echo, IncorporatedAll Rights Reserved.TABLE OF CONTENTSIntroduction ...

20BLADE REPLACEMENT/LUBRICATIONLevel 1.Tools Required: Scrench, Locking Tool, Needle Nose Pliers, 8 mmOpen End WrenchParts Required: ECHO® LUBETM 8 oz

POWER EDGEROPERATOR'S MANUAL21TROUBLESHOOTINGWARNING DANGERFuel vapors are extremely flammable and may cause fire and/or explosion. Neve

22STORAGEWARNING DANGERDuring operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clearof flamm

POWER EDGEROPERATOR'S MANUAL23NOTES

SERVICING INFORMATIONPARTSGenuine ECHO Parts and ECHO REPOWER™ Parts and Assemblies foryour ECHO products are available only from an Authorized ECHODe

POWER EDGEROPERATOR'S MANUAL3SAFETYDECALSLocate these safety decals on your unit. Make sure the decals arelegible and that you understand and fo

4INTERNATIONAL SYMBOLSSAFETY I NSTRUCTIONSPERSONAL CONDITION AND SAFETY EQUIPMENTWARNING DANGEREdger users risk injury to themselves and others

POWER EDGEROPERATOR'S MANUAL5EXTENDED OPERATION/EXTREME CONDITIONSVibration and ColdIt is believed that a condition called Raynaud’s Phenomenon,

6SAFE OPERATIONWARNING DANGERDo not operate this product indoors or in inadequately ventilatedareas. Engine exhaust contains poisonous emissions

POWER EDGEROPERATOR'S MANUAL7DESCRIPTIONThe ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging rest

81. POWER HEAD - Factory assembled. Includes the engine, clutch, fuel system, ignition system and starter.2. GRIP - Rear (right hand) handle.3. FRONT

POWER EDGEROPERATOR'S MANUAL9SPECIFICATIONSMODEL -----------------------------------------------------PE-200Length ------------------------------