OW N E R ' S M A N UA LManual P/N 14688-00S Rev. 12/06Companion to P/N 14689-00SMADE WITH PRIDE IN THE...6 INCH CHIPPER 74624S - 24 HP HONDA
8SAFETYSee Section 1.11 for decal locations. Familiarize yourself with all of the safety and operating decals on the machine and the associated hazar
9SAFETYThe numbers below correspond to the decals in Section 1.10. Familiarize yourself with all of the safety and operational decals on the machine
10ASSEMBLYBefore inspecting or servicing any part of this machine, shut off power source, disengage the hydraulics, remove igni-tion key and ma
11ASSEMBLY2.7 ADDING MOTOR OIL TO ENGINEThe machine was shipped with oil in the engine, as it was tested at the factory.To determine which type
12FEATURES & CONTROLSUnderstanding how your machine works will help you achieve the best results when using your chipper. The following descripti
13FEATURES & CONTROLSDiesel control panelGas control panel1. CHIPPER ENGAGEMENT: To activate, slowly push the handle toward the ground. To diseng
14Section OPERATIONAs with any other piece of outdoor power equipment, get-ting the feel for how your machine operates and getting to know the best t
15OPERATION4.2 STARTING A GASOLINE CHIPPER4.3 STARTING A DIESEL CHIPPERMake sure the cutting chamber is empty before starting. Reference the Honda
16OPERATION4.4 CHIPPINGWARNINGThe Bear Cat chipper is designed to chip a variety of materials into a more readily decomposing or ha
17OPERATION4.6 HYDRAULIC FEED CONTROLThe Bear Cat chipper is equipped with a pre-programmed hydraulic feed control located under the control panel.
Before You BeginDEAR CRARY BEAR CAT CUSTOMERThank you for purchasing a Crary Bear Cat product. The Crary Bear Cat line is designed, tested, and manuf
18OPERATION4.8 FEED ROLLER BOTTLE JACKMove throttle to slowest position.Move chipper engagement to the engine start posi-tion.Let machine idle
195.1 MAINTENANCE SCHEDULESERVICE & MAINTENANCEThe items listed in the service and maintenance schedule are to be checked, and if necessary, cor
20SERVICE & MAINTENANCEBEFORE INSPECTING OR SERVICING ANY PART OF THIS MACHINE, SHUT OFF POWER SOURCE, DISENGAGE THE HYDRAULICS, OPEN SHIELD AND
21SERVICE & MAINTENANCEBEFORE INSPECTING OR SERVICING ANY PART OF THIS MACHINE, SHUT OFF POWER SOURCE, DISENGAGE THE HYDRAULICS, OPEN SHIELD AND
22SERVICE & MAINTENANCEBEFORE INSPECTING OR SERVICING ANY PART OF THIS MACHINE, SHUT OFF POWER SOURCE, DISENGAGE THE HYDRAULICS, OPEN SHIELD AND
23SERVICE & MAINTENANCEBEFORE INSPECTING OR SERVICING ANY PART OF THIS MACHINE, SHUT OFF POWER SOURCE, DISENGAGE THE HYDRAULICS, OPEN SHIELD AND
24SERVICE & MAINTENANCEBEFORE INSPECTING OR SERVICING ANY PART OF THIS MACHINE, SHUT OFF POWER SOURCE, DISENGAGE THE HYDRAULICS, OPEN SHIELD AND
25SERVICE & MAINTENANCEBEFORE INSPECTING OR SERVICING ANY PART OF THIS MACHINE, SHUT OFF POWER SOURCE, DISENGAGE THE HYDRAULICS, OPEN SHIELD AND
26Before performing any of the corrections in this troubleshooting chart, refer to the appropriate information contained in this manual for the correc
27SPECIFICATIONSThe tables shown below give correct torque values for various bolts and capscrews. Tighten all bolts to the torques specied in chart
1LIMITED WARRANTYThis warranty applies to all AG and Outdoor Power Equipment manufactured by Crary Industries.Crary Industries warrants to the origina
Crary Industries237 NW 12th Street, West Fargo, ND 58078-0849 Phone: 701.282.5520 • Toll Free: 800.247.7335Fax: 701.282.9522 • E-mail: [email protected]
2TABLE OF CONTENTSDESCRIPTION PAGE DESCRIPTION PAGE SAFETY ... 31.1 S
3Section SAFETYThe Owner/Operator's manual uses this symbol to alert you of potential hazards. Whenever you see this symbol, read and
4SAFETYOne of the critical moments in job safety, as well as chipper safety, is setting up your chipping site so you are not endangered by traffic, an
5SAFETYAlways stand clear of discharge area when operating this machine. Keep face and body away from feed and discharge openings.Keep hands and fee
6SAFETYDANGER / POISON SHIELD EYESEXPLOSIVE GASES CAN CAUSEBLINDNESS ORINJURY NO• SPARKS• FLAMES• SMOKINGSULFURIC ACIDCAN CAUSEBLINDN
7SAFETYSee Section 1.11 for decal locations. Familiarize yourself with all of the safety and operating decals on the machine and the associated hazar
Kommentare zu diesen Handbüchern