OWNER'S MANUAL5 INCH CHIPPERCH5540H - 540 PTO HYDRAULIC FEEDPN: 12666 Rev. 013009 Companion to 12665SN Range: 805149 to A03529
65 INCH CHIpperSection2ASSEMBLYMount the feed chute to the chipper housing using six (6) 1. 3/8 x 1-1/4" carriage bolts, 3/8" washers, and 3
7 5 INCH CHIpperASSEMBLY2.4.1 CHECK LENGTH OF PTO DRIVELINEAttach chipper to tractor with three-point hitch. 1. You must make sure that the PTO drive
85 INCH CHIpperSectionBelt Guard: Remove to grease rotor and jack shafts and to check or replace belt.Discharge Lock: Used to pivot and lock the disch
9 5 INCH CHIpperSectionWARNINGWARNINGRead and understand all safety warnings and chipping 1. guidelines contained in this manual before proceeding.Con
105 INCH CHIpperOPERATIONThe machine chips a variety of materials into a more readily decomposed or handled condition. The following gu
11 5 INCH CHIpperSectionWARNING5SERVICE & MAINTENANCE5.2 SERVICE AND MAINTENANCE SCHEDULESERVICE AND MAINTENANCE SCHEDULECOMPONENTMAINTENANCE REQ
125 INCH CHIpperSERVICE & MAINTENANCEChipping blades are sharp! Use caution when working on machine to avoid injury.To remove the chipping blades
13 5 INCH CHIpperSERVICE & MAINTENANCEFigure 5.2 Sharpening the bladesThe chipping blades should clear the anvil by 1/16 inch to 1/8 inch. Check
145 INCH CHIpperSERVICE & MAINTENANCEFigure 5.5 Belt and pulleys with belt shield removedIDLER PULLEYJACK SHAFTLubricate the machine periodic
15 5 INCH CHIpperSERVICE & MAINTENANCE1. Remove the one 3/8" retaining bolt holding access cover to main frame assembly. Tilt access
Before You BeginDEAR ECHO BEAR CAT CUSTOMERThank you for purchasing a ECHO Bear Cat product. The ECHO Bear Cat line is designed, tested, and manufact
165 INCH CHIpperSERVICE & MAINTENANCECAUTIONHandle pressurized hydraulic uid carefully. Escaping pressurized hydraulic uid can have sufcient fo
17 5 INCH CHIpperSection6TROUBLESHOOTINGBefore performing any of the corrections in this troubleshooting chart, refer to the appropriate information c
185 INCH CHIpperSectionSPECIFICATIONS7CH5540HDESCRIPTION English MetricOVERALL SIZE 150" x 73" x 90"381cm x 185cm x 228cm OVERALL WEIGH
19 5 INCH CHIpperSPECIFICATIONS7.2 BOLT TORQUEBOLT DIAMETER (A)METRICBOLT TORQUE *4.8 8.8 10.9 12.9N.m Ft-lb. N.m Ft-lb. N.m Ft-lb. N.m Ft-lb.M3 0.5
Declaration of Conformity The undersigned manufacturer: Crary Industries, Inc. 237 NW 12th Street P.O. Box 849 West Fargo, ND 58078-0849 Declares
ECHO BEAR CAT 237 NW 12th Street, West Fargo, ND 58078-0849 Phone: 701.282.5520 • Toll Free: 800.247.7335Fax: 701.282.9522 E-mail: [email protected] •
LIMITED WARRANTYThis warranty applies to all AG and Outdoor Power Equipment manufactured by Crary Industries.Crary Industries warrants to the original
iv5 INCH CHIpperContentsSAFETY ... 11.1
1 5 INCH CHIpperSection1SAFETYThe Owner/Operator's manual uses this symbol to alert you of potential hazards. Whenever you see this symbol,
25 INCH CHIpperSAFETY1.3 OPERATION SAFETY1.5 MAINTENANCE AND STORAGE1.4 FEED ROLLER SAFETYAlways stand clear of discharge area when operating 1. t
3 5 INCH CHIpperOPERATION1.6 PTO SAFETYRead and follow instructions on PTO safety decals.1. Stay alert and pay attention when PTO is operating.2. Kee
45 INCH CHIpperSAFETY1.7 SAFETY DECAL LOCATIONSSee Section 1.8 for decal descriptions. Familiarize yourself with all of the safety and operating dec
5 5 INCH CHIpperSAFETYSee Section 1.7 for decal locations. Familiarize yourself with all of the safety and operating decals on the machine and the as
Kommentare zu diesen Handbüchern