SHRED'N'VAC® Operator's Manual MODEL ES-255 X75001194411/09X7501180704 WARNINGRead rules for saf
10v a C u u m /s h r e d d I n g a p p l I C a T I o nRemove Blower Pipes 1. Release locking ring (C) with a coin or screwdriver, and rotate ring s
11Sh r e d 'N'Va c® Op e r a t O r 'S Ma N u a lInstall Bag 1. Stand unit upright on blower base. 2. Release locking ring (C) with
12NOTICE: Use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting, poor performance, or severe engine dama
13Sh r e d 'N'Va c® Op e r a t O r 'S Ma N u a lMixing Instructions 1. Fill an approved fuel container with half of the required amo
14s T a r T I n g C o l d e n g I n e 1. Stop Switch Move stop switch button (A) away from the STOP position. 2. Throttle Position
15Sh r e d 'N'Va c® Op e r a t O r 'S Ma N u a ls T a r T I n g w a r m e n g I n eThe starting procedure is the same as Cold Start ex
16Read the Safety Section carefully.IMPORTANT To avoid engine damage due to over-revving, do not block blower pipe. 1. Use only during appropriate
17Sh r e d 'N'Va c® Op e r a t O r 'S Ma N u a l 1. Adjust debris bag strap to support bag on operator’s shoulder. Bag must not be fo
18Your ECHO blower is designed to provide many hours of trouble free service. Regular scheduled maintenance will help your blower achieve that goal. I
19Sh r e d 'N'Va c® Op e r a t O r 'S Ma N u a lf u e l f I l T e rLevel 1.Tools required: 200-250 mm (8-10 in.) length of wire wit
2Copyright© 2010 By Echo, IncorporatedAll Rights Reserved.Ta b l e o f Co n T e n T sIntroduction ...
200.65 mm(0.026 in.)C o o l I n g s y s T e mLevel 2.Tools required: 25-50 mm (1-2 in.) cleaning brush, 4 mm Hex Wrench.Parts Required:
21Sh r e d 'N'Va c® Op e r a t O r 'S Ma N u a le x h a u s T s y s T e mSpark Arrestor ScreenLevel 2.Tools required: Cross Head Scr
22ABExhaust Port CleaningLevel 2.Tools required: 4 mm Hex Wrench., Wood or plastic scraperParts Required: As needed: Heat Shield1. Remove spar
23Sh r e d 'N'Va c® Op e r a t O r 'S Ma N u a ls h r e d d e r b l a d eLevel 1. WARNING Never remove vacuum tube or open fan gua
24C a r b u r e T o r a d j u s T m e n TEngine Break-InNew engines must be operated a minimum duration of two tanks of fuel break-in before carburet
25Sh r e d 'N'Va c® Op e r a t O r 'S Ma N u a l DANGERFuel vapors are extremely ammable and may cause re and/or explosion. Neve
26sT o r a g e WARNINGDuring operation the mufer or catalytic mufer and surrounding cover becomes hot. Always keep exhaust area clear of ammab
27Sh r e d 'N'Va c® Op e r a t O r 'S Ma N u a lsp e C I f I C a T I o n sMODEL -------------------------------------------------------
28ECHO LIMITED WARRANTY STATEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010ECHO'S RESPONSIBILITYECHO Incorporated’s Limited Warrant
29Sh r e d 'N'Va c® Op e r a t O r 'S Ma N u a lPURCHASED REPAIR PARTS, SHORT BLOCKS AND ACCESSORIES
3Sh r e d 'N'Va c® Op e r a t O r 'S Ma N u a lsa f e T ym a n u a l s a f e T y s y m b o l s a n d I m p o r T a n T I n f o r m
30 ECHO INCORPORATED EMISSION CONTROL WARRANTY STATEMENTFOR ECHO AND SHINDAIWA BRANDSThe Environmental Protection Agency (EPA) and the California Air
31Sh r e d 'N'Va c® Op e r a t O r 'S Ma N u a ln o T e s
CONSUMER PRODUCTSUPPORT1-800-673-15588:30 - 4:30 Mon - Fri C.S.T.ECHO, INCORPORATED400 Oa k w O O d RO a dla k e Zu r I C h , Il 60047-1564www.echo
4Physical Condition Your judgment and physical dexterity may not be good: • if you are tired or sick, •
5Sh r e d 'N'Va c® Op e r a t O r 'S Ma N u a l DANGERDo not operate this product indoors or in inadequately ventilated areas. Engi
6e q u I p m e n T C h e C k WARNINGUse only ECHO approved attachments. Serious injury may result from the use of a non-approved attachment comb
7Sh r e d 'N'Va c® Op e r a t O r 'S Ma N u a lde s C r I p T I o nLocate the safety decal on your unit. Make sure the decals are legi
8 1. SAFETY DECAL - Lists important safety precautions. 2. STOP SWITCH - "SLIDE SWITCH" mounted on top of handle. Push forward to start
9Sh r e d 'N'Va c® Op e r a t O r 'S Ma N u a las s e m b l y WARNINGNever perform maintenance or assembly procedures with engine
Kommentare zu diesen Handbüchern