Echo CS-440 Bedienungsanleitung

OPERATOR’S MANUALCHAIN SAWCS-440X750-006 21 4X750 319-510 4ECHO POWER EQUIPMENT (CANADA)501 Newbold Street, London, Ontario Canada N6E 1K4 WARNINGRe

10CS-440PREPARATION FOR USEBolt (A)Dimple (D)Recess (E)Front hole (C)Rear hole (B)Nut (F)Guide barKick Guard® WARNINGSaw Chain is sharp! Always wear

11CS-4405. Mount guide bar on studs and slide toward clutchto make saw chain installation easier. Installchain with cutters on top of guide bar facing

12CS-440IMPORTANT• ECHO premium Power Blend™ Universal 2-Stroke Oil may be mixed at 50 : 1 ratio forapplication in all ECHO engines sold in the pastre

13CS-440

14CS-440WHEN THE ENGINE IS HARD TOSTART CAUTIONMake sure the bar and chain are free fromany obstruction when starting the chain saw.• Move chain bra

15CS-440RUNNING• When engine starts, keep idling for a fewminutes.• Set the brake lever in the unlocked positionbefore starting to cut.• Pull throttle

16CS-440CUTTING INSTRUCTIONGENERAL CAUTION• Read the ECHO “CHAIN SAW SAFETYMANUAL” included with your chain saw foradditional cutting and safety ins

17CS-440FELLING THE TREEA falling tree can seriously damage anything it mayhit - a car, a house, a fence, a power-line, oranother tree.There are ways

18CS-440LIMBINGLimbing a fallen tree is much the same as bucking.Never remove a limb from a tree while it issupporting your weight.When limbing, cauti

19CS-440Chain brake functionWhen the lever is pushed forward, chain brakeinstantly stops the chain.Chain brake unlockWhen the lever is fully pulled, t

2CS-440Copyright © 2003 All Rights Reserved. 1. Fatigue causes carelessness. Be morecautious before rest periods and beforethe end of your shift.

20CS-440END OF THE GUIDE BAR may be placed atthe height of about 35 cm.35 cmRear handle should be gripped lightly withthe right hand.AUTOMATIC CHAIN B

21CS-440CHAIN AND GUIDE BAR COMBINATIONGuide Bar Saw ChainLength ECHO Part No. Pitch Type Linksmm (in.) Double Guard mm (in.) (OREGON) 406 (16) 16A0AD

22CS-440MAINTENANCE AND CAREComponent/system Maintenance procedureRecommended ECHO Dealer Maintenance ProceduresCylinder Exhaust Port Inspect/Clean/De

23CS-440CARBURETOR ADJUSTMENTEvery unit is run at the factory and the carburetor isset in compliance with Emission Regulations. Inaddition, the carbur

24CS-4400.6 to 0.7 mmAIR FILTER• Check before every use.• Loosen three screws and remove air cleanercover and filter.• Brush off dust lightly, or clea

25CS-440Worn : 0.5 mmGUIDE BAR• Clean before using.- Clean the groove of the guide bar with a smallscrewdriver.- Clean oil holes with a wire.• Check s

26CS-440SETTING THE SAW CHAINSharpen lower edgeDrive linkTie strapRight hand cutterPreset tie strapLeft hand cutterGuard linkTop plateSide plateDepth

27CS-440NOTEThese angles are referred to as Oregon 33SL.To sharpen other follow chain manufacturer’sinstruction.• Place the depth gauge tool firmly on

28CS-440TROUBLESHOOTINGProblemEngine — hard to start Cause Remedy— does not startEngine Fuel at No fuel • Fuel filter clogged • Clean or replacecranks

29CS-440CS-440Dimension L × W × H mm 398 × 252 × 272Mass Power head, dry kg 4.8Without chain and guide barEngine Type Air-cooled two-stroke single cyl

3CS-440 WARNINGThe safety alert symbol accompanied by theword “WARNING” calls attention to an act orcondition which CAN lead to seriouspersonal inju

4CS-440Carburetor adjustment- Idle speedCarburetor adjustment- High speed mixtureCarefully read the operator’smanualWear eyes, ears and headprotection

5CS-440PACKING LISTThe ECHO product you purchased has beenfactory pre-assembled for your convenience. Due topackaging restrictions, guide bar and saw

6CS-440

7CS-440NOMENCLATURE OF PARTS1. Operator’s manual - Included with unit.Read before operation and keep for futurereference to learn proper, safe operati

8CS-440VIBRATION AND COLD• It is believed that a condition called Raynaud’sPhenomenon, which affects the fingers of certainindividuals, may be brought

9CS-440